Applied Sciences, Vol. 6, Pages 32: Research on a Composite Power-Superimposed Ultrasonic Vibrator for Wire Drawing

Vibration power and amplitude are essential factors in ultrasonic drawing processes, especially for difficult-to-draw materials like titanium and its alloys. This paper presents a new composite power-superimposed ultrasonic vibrator for wire drawing which was driven by three separate ultrasonic transducers. The transducers were uniformly distributed around the circular cross section of the vibrator, with their axes along the radial direction and pointing to the center. The vibrator can concentrate the vibrational energy of multiple transducers and transform the radial vibration into a longitudinal vibrator because of the Poisson effect and therefore output larger vibration power and amplitude. In the paper, the four-terminal network method was used to establish the vibration equations of the vibrator. The FE model was established in ANSYS to investigate its characteristics under various excitation conditions. A prototype was manufactured and measurements were performed to verify the validation of FEA results. The results matched well with the theoretical results. It was found that the composite vibrator achieved an amplitude of about 40 μm when driven by square wave signals with 120° in phase difference, which implies a potential way of applying ultrasonic vibration to the processing of difficult-to-draw materials.

from #Medicine via ola Kala on Inoreader http://ift.tt/1SH59d6
via IFTTT

Applied Sciences, Vol. 6, Pages 31: Phosphorus Distribution in Soils from Australian Dairy and Beef Rearing Pastoral Systems

The influence of soil type and management practices on P distribution in soils from Australian dairy and beef rearing pastoral systems has been investigated by chemical measurements and phosphorus-31 (31P) nuclear magnetic resonance (NMR) spectroscopy. The amount and forms of P within the soil profile varied with soil type, with the acidic red Ferrosols containing relatively high orthophosphate concentrations, averaging 72.2% compared with 66.8% for Dermosols, under similar management conditions. Soil from Sodosol sites which received less fertiliser P addition had the lowest orthophosphate concentration with only 57.6%. In contrast, relatively high proportions of organic P were found in soil samples from unfertilised Sodosol sites. On average, soil from Sodosol sites contained 37.5% organic P (combined monoester P and diester P), while those from Dermosol and Ferrosol sites contained 31.7% and 25.8%, respectively. Of these, the highest monoester phosphate proportions of 44.6% (site M3) and 46.4% (site M4) were found in Sodosol sites with no recent P inputs, but the highest proportion of diester phosphate (5.7%) was found in an unclassified grey sandy loam Dermosol. The higher organic P concentrations in soil from Sodosol sites may be associated with more regular moisture input from both rainfall and boarder-check (flood) irrigation. The highest level of pyrophosphate (8.5%) was also found in a grey/yellow Sodosol. Overall, the results indicate that P speciation in the Australian soils is strongly influenced by soil type, fertiliser P application rate and timing, and moisture variations.

from #Medicine via ola Kala on Inoreader http://ift.tt/1SH5bSp
via IFTTT

Applied Sciences, Vol. 6, Pages 33: Proof of Concept of Crack Localization Using Negative Pressure Waves in Closed Tubes for Later Application in Effective SHM System for Additive Manufactured Components

Additive manufactured components have a different metallurgic structure and are more prone to fatigue cracks than conventionally produced metals. In earlier papers, an effective Structural Health Monitoring solution was presented to detect fatigue cracks in additive manufactured components. Small subsurface capillaries are embedded in the structure and pressurized (vacuum or overpressure). A crack that initiated at the component's surface will propagate towards the capillary and finally breach it. One capillary suffices to inspect a large area of the component, which makes it interesting to locate the crack on the basis of the pressure measurements. Negative pressure waves (NPW) arise from the abrupt encounter of high pressure fluid with low pressure fluid and can serve as a basis to locate the crack. A test set-up with a controllable leak valve was built to investigate the feasibility of using NPW to localize a leak in closed tubes with small lengths. Reflections are expected to occur at the ends of the tube, possibly limiting the localization accuracy. In this paper, the results of the tests on the test set-up are reported. It will be shown that the crack could be localized with high accuracy (millimeter accuracy) which proves the concept of crack localization on basis of NPW in a closed tube of small length.

from #Medicine via ola Kala on Inoreader http://ift.tt/1PwXgjO
via IFTTT

Magnetochemistry, Vol. 2, Pages 4: Magnetochemistry: From Fundamentals to Applications

It is well knowm that Magnetochemistry is a multidisplinary area that deals with many different materials and properties. [...]

from #Medicine via ola Kala on Inoreader http://ift.tt/1PwXebO
via IFTTT

Machines, Vol. 4, Pages 5: Joint Mechanism That Mimics Elastic Characteristics in Human Running

Analysis of human running has revealed that the motion of the human leg can be modeled by a compression spring because the joints of the leg behave like a torsion spring in the stance phase. In this paper, we describe the development of a joint mechanism that mimics the elastic characteristics of the joints of the stance leg. The knee was equipped with a mechanism comprising two laminated leaf springs made of carbon fiber-reinforced plastic for adjusting the joint stiffness and a worm gear in order to achieve active movement. Using this mechanism, we were able to achieve joint stiffness mimicking that of a human knee joint that can be adjusted by varying the effective length of one of the laminated leaf springs. The equation proposed for calculating the joint stiffness considers the difference between the position of the fixed point of the leaf spring and the position of the rotational center of the joint. We evaluated the performance of the laminated leaf spring and the effectiveness of the proposed equation for joint stiffness. We were able to make a bipedal robot run with one leg using pelvic oscillation for storing energy produced by the resonance related to leg elasticity.

from #Medicine via ola Kala on Inoreader http://ift.tt/1SH5bls
via IFTTT

Education Sciences, Vol. 6, Pages 2: Terminology Standardization in Education and the Construction of Resources: The Welsh Experience

This paper describes developments in Welsh-language terminology within the education system in Wales. Following an outline of historical terminology work, it concentrates on the consolidation of terminology standardization at the Language Technologies Unit, Bangor University, with particular reference to two projects, one concerned with terminology for school-age and further education, the second concerned with higher education. The developments described include the adoption of international standards in terminology standardization and their incorporation in an online terminology standardization environment and dissemination platform that enable access to the centralized terminological dictionaries via a number of sophisticated websites, portals and mobile apps featuring rich dictionary entries. Some of the issues in managing large term collections are explored, and usage statistics are presented for the resources described.

from #Medicine via ola Kala on Inoreader http://ift.tt/1PwXfwv
via IFTTT

Micromachines, Vol. 7, Pages 19: Two-Layer Microstructures Fabricated by One-Step Anisotropic Wet Etching of Si in KOH Solution

Anisotropic etching of silicon in potassium hydroxide (KOH) is an important technology in micromachining. The residue deposition from KOH etching of Si is typically regarded as a disadvantage of this technology. In this report, we make use of this residue as a second masking layer to fabricate two-layer complex structures. Square patterns with size in the range of 15–150 μm and gap distance of 5 μm have been designed and tested. The residue masking layer appears when the substrate is over-etched in hydrofluoric acid (HF) solution over a threshold. The two-layer structures of micropyramids surrounded by wall-like structures are obtained according to the two different masking layers of SiO2 and residue. The residue masking layer is stable and can survive over KOH etching for long time to achieve deep Si etching. The process parameters of etchant concentration, temperature, etching time and pattern size have been investigated. With well-controlled two-layer structures, useful structures could be designed for applications in plasmonic and microfluidic devices in the future.

from #Medicine via ola Kala on Inoreader http://ift.tt/1PwXfg3
via IFTTT

Mathematics, Vol. 4, Pages 4: Acknowledgement to Reviewers of Mathematics in 2015

The editors of Mathematics would like to express their sincere gratitude to the following reviewers for assessing manuscripts in 2015. [...]

from #Medicine via ola Kala on Inoreader http://ift.tt/1SH57SC
via IFTTT

IJERPH, Vol. 13, Pages 158: Association Between Smoking and Physician-Diagnosed Stroke and Myocardial Infarction in Male Adults in Korea

To evaluate the association between smoking and physician-diagnosed stroke and myocardial infarction, this study used Community Health Survey data from 2009 on 92,082 males over the age of 30 years. Using multiple logistic regression, association index between smoking and physician-diagnosed stroke and myocardial infarction was calculated after adjusting the effects of age, hypertension, and diabetes. The odds ratios (95% confidence interval) of the physician-diagnosed stroke and myocardial infarction in the smoking group were 1.12 (1.02–1.24) and 1.21 (1.06–1.38) compared to the non-smoking group. The values of the physician-diagnosed stroke and myocardial infarction were 0.84 (0.74–0.94) and 0.96 (0.82–1.12) in the current-smoking subgroup, 1.38 (1.24–1.53) and 1.45 (1.26–1.67) in the ex-smoking subgroup, 1.39 (1.18–1.63) and 1.85 (1.53–2.24) in the 10- to 19-year smokers groups, 1.39 (1.22–1.58) and 1.36 (1.15–1.60) in the 30- to 40-year smokers groups, and 0.53 (0.44–0.63) and 0.47 (0.36–0.63) in those who had smoked for over 50 years. These results showed smoking was a risk factor for stroke and myocardial infarction in Korean males. This objective evidence should guide policy-making and public health interventions in the fields of smoking prevention and prohibition.

from #Medicine via ola Kala on Inoreader http://ift.tt/1SH57Sv
via IFTTT

JMSE, Vol. 4, Pages 5: Dynamically Scaled Model Experiment of a Mooring Cable

The dynamic response of mooring cables for marine structures is scale-dependent, and perfect dynamic similitude between full-scale prototypes and small-scale physical model tests is difficult to achieve. The best possible scaling is here sought by means of a specific set of dimensionless parameters, and the model accuracy is also evaluated by two alternative sets of dimensionless parameters. A special feature of the presented experiment is that a chain was scaled to have correct propagation celerity for longitudinal elastic waves, thus providing perfect geometrical and dynamic scaling in vacuum, which is unique. The scaling error due to incorrect Reynolds number seemed to be of minor importance. The 33 m experimental chain could then be considered a scaled 76 mm stud chain with the length 1240 m, i.e., at the length scale of 1:37.6. Due to the correct elastic scale, the physical model was able to reproduce the effect of snatch loads giving rise to tensional shock waves propagating along the cable. The results from the experiment were used to validate the newly developed cable-dynamics code, MooDy, which utilises a discontinuous Galerkin FEM formulation. The validation of MooDy proved to be successful for the presented experiments. The experimental data is made available here for validation of other numerical codes by publishing digitised time series of two of the experiments.

from #Medicine via ola Kala on Inoreader http://ift.tt/1PwXd7K
via IFTTT

IJMS, Vol. 17, Pages 152: Mesenchymal Stem Cells Preserve Working Memory in the 3xTg-AD Mouse Model of Alzheimer’s Disease

The transplantation of stem cells may have a therapeutic effect on the pathogenesis and progression of neurodegenerative disorders. In the present study, we transplanted human mesenchymal stem cells (MSCs) into the lateral ventricle of a triple transgenic mouse model of Alzheimer´s disease (3xTg-AD) at the age of eight months. We evaluated spatial reference and working memory after MSC treatment and the possible underlying mechanisms, such as the influence of transplanted MSCs on neurogenesis in the subventricular zone (SVZ) and the expression levels of a 56 kDa oligomer of amyloid β (Aβ*56), glutamine synthetase (GS) and glutamate transporters (Glutamate aspartate transporter (GLAST) and Glutamate transporter-1 (GLT-1)) in the entorhinal and prefrontal cortices and the hippocampus. At 14 months of age we observed the preservation of working memory in MSC-treated 3xTg-AD mice, suggesting that such preservation might be due to the protective effect of MSCs on GS levels and the considerable downregulation of Aβ*56 levels in the entorhinal cortex. These changes were observed six months after transplantation, accompanied by clusters of proliferating cells in the SVZ. Since the grafted cells did not survive for the whole experimental period, it is likely that the observed effects could have been transiently more pronounced at earlier time points than at six months after cell application.

from #Medicine via ola Kala on Inoreader http://ift.tt/1SH54Gx
via IFTTT

Social Sciences, Vol. 5, Pages 4: Acknowledgement to Reviewers of Social Sciences in 2015

The editors of Social Sciences would like to express their sincere gratitude to the following reviewers for assessing manuscripts in 2015. [...]

from #Medicine via ola Kala on Inoreader http://ift.tt/1ZMRznK
via IFTTT

Antioxidants, Vol. 5, Pages 5: Acknowledgement to Reviewers of Antioxidants in 2015

The editors of Antioxidants would like to express their sincere gratitude to the following reviewers for assessing manuscripts in 2015. [...]

from #Medicine via ola Kala on Inoreader http://ift.tt/1S5q7mk
via IFTTT

Sports, Vol. 4, Pages 5: ZumBeat: Evaluation of a Zumba Dance Intervention in Postmenopausal Overweight Women

Physical inactivity is a major public health concern since it increases individuals' risk of morbidity and mortality. A subgroup at particular risk is postmenopausal overweight women. The aim of this study was to assess the feasibility and effect of a 12-week ZumBeat dance intervention on cardiorespiratory fitness and psychosocial health. Postmenopausal women with a body mass index (BMI) >30 kg/m2 or a waist circumference >94 cm who were not regularly physically active were asked to complete a 12-week ZumBeat dance intervention with instructed and home-based self-training sessions. Before and after the intervention, peak oxygen consumption (VO2peak) was assessed on a treadmill; and body composition and several psychometric parameters (including quality of life, sports-related barriers and menopausal symptoms) were investigated. Of 17 women (median age: 54 years; median BMI: 30 kg/m2) enrolled in the study, 14 completed the study. There was no apparent change in VO2peak after the 12-week intervention period (average change score: −0.5 mL/kg/min; 95% confidence interval: −1.0, 0.1); but, quality of life had increased, and sports-related barriers and menopausal symptoms had decreased. A 12-week ZumBeat dance intervention may not suffice to increase cardiorespiratory fitness in postmenopausal overweight women, but it increases women's quality of life.

from #Medicine via ola Kala on Inoreader http://ift.tt/1ZMRBfv
via IFTTT

Water, Vol. 8, Pages 38: Sediment Deposition at the Caernarvon Crevasse during the Great Mississippi Flood of 1927: Implications for Coastal Restoration

During the 1927 Mississippi flood, the levee was dynamited downstream of New Orleans creating a 2 km wide crevasse that inundated the Breton Sound estuary and deposited a crevasse splay of about 130 km2. We measured sediment deposition in the splay that consisted of a silty-clay layer bounded by aged peat below and living roots above. Based on coring, we developed a map of the crevasse splay. The clay layer ranged from 2 to 42 cm thick and occurred 24 to 55 cm below the surface. Bulk density of the clay layer decreased and soil organic matter increased with distance from the river. 210Pbexcess and 137Cs dating an age of ~1926–1929 for the top of the layer. During the flood event, deposition was at least 22 mm·month−1—10 times the annual post-1927 deposition. The crevasse splay captured from 55% to 75% of suspended sediments that flowed in from the river. The 1927 crevasse deposition shows how pulsed flooding can enhance sediment capture efficiency and deposition and serves as an example for large planned diversions for Mississippi delta restoration.

from #Medicine via ola Kala on Inoreader http://ift.tt/1S5q75Z
via IFTTT

Energies, Vol. 9, Pages 69: An Innovative Control Strategy to Improve the Fault Ride-Through Capability of DFIGs Based on Wind Energy Conversion Systems

An innovative control strategy is proposed for enhancing the low voltage ride-through (LVRT) capability of a doubly fed induction generator based on wind energy conversion systems (DFIG-WECS). Within the proposed control method, the current control loops of the rotor side converter (RSC) are developed based on passivity theory. The control scheme for the grid side converter (GSC) is designed based on a two-term approach to keep the DC-link voltage close to a given value. The first term based on the maximal voltage of GSC is introduced in the GSC control loops as a reference reactive current. The second one reflecting the instantaneous unbalanced power flow between the RSC and GSC is also introduced in the GSC control loops as a disturbance considering the instantaneous power of the grid filter to compensate the instantaneous rotor power. The effectiveness of the proposed control strategy is verified via time domain simulation of a 2.0 MW-575 V DFIG-WECS using PSCAD/EMTP. Simulation results show that the control of the DFIG with the proposed approach can improve the LVRT capability better than with the conventional one.

from #Medicine via ola Kala on Inoreader http://ift.tt/1ZMRBfr
via IFTTT

Applied Sciences, Vol. 6, Pages 34: A Physically—Based Geometry Model for Transport Distance Estimation of Rainfall-Eroded Soil Sediment

Estimations of rainfall-induced soil erosion are mostly derived from the weight of sediment measured in natural runoff. The transport distance of eroded soil is important for evaluating landscape evolution but is difficult to estimate, mainly because it cannot be linked directly to the eroded sediment weight. The volume of eroded soil is easier to calculate visually using popular imaging tools, which can aid in estimating the transport distance of eroded soil through geometry relationships. In this study, we present a straightforward geometry model to predict the maximum sediment transport distance incurred by rainfall events of various intensity and duration. In order to verify our geometry prediction model, a series of experiments are reported in the form of a sediment volume. The results show that cumulative rainfall has a linear relationship with the total volume of eroded soil. The geometry model can accurately estimate the maximum transport distance of eroded soil by cumulative rainfall, with a low root-mean-square error (4.7–4.8) and a strong linear correlation (0.74–0.86).

from #Medicine via ola Kala on Inoreader http://ift.tt/1S5q6Pr
via IFTTT

Experimental modulation of external microbiome affects nestmate recognition in harvester ants (Pogonomyrmex barbatus)

Social insects use odors as cues for a variety of behavioral responses, including nestmate recognition. Past research on nestmate recognition indicates cuticular hydrocarbons are important nestmate discriminators for social insects, but other factors are likely to contribute to colony-specific odors. Here we experimentally tested whether external microbes contribute to nestmate recognition in red harvester ants (Pogonomyrmex barbatus). We changed the external microbiome of ants through topical application of either antibiotics or microbial cultures. We then observed behavior of nestmates when treated ants were returned to the nest. Ants whose external microbiome was augmented with microbial cultures were much more likely to be rejected than controls, but ants treated with antibiotics were not. This result is consistent with the possibility that external microbes are used for nestmate recognition.

from #Medicine via ola Kala on Inoreader http://ift.tt/23nk2VN
via IFTTT

First insights into the diversity of gill monogeneans of ‘Gnathochromis’ and Limnochromis (Teleostei, Cichlidae) in Burundi: do the parasites mirror host ecology and phylogenetic history?

Monogenea is one of the most species-rich groups of parasitic flatworms worldwide, with many species described only recently, which is particularly true for African monogeneans. For example, Cichlidogyrus, a genus mostly occurring on African cichlids, comprises more than 100 nominal species. Twenty-two of these have been described from Lake Tanganyika, a famous biodiversity hotspot in which many vertebrate and invertebrate taxa, including monogeneans, underwent unique and spectacular radiations. Given their often high degrees of host specificity, parasitic monogeneans were also used as a potential tool to uncover host species relationships. This study presents the first investigation of the monogenean fauna occurring on the gills of endemic 'Gnathochromis' species along the Burundese coastline of Lake Tanganyika. We test whether their monogenean fauna reflects the different phylogenetic position and ecological niche of 'Gnathochromis' pfefferi and Gnathochromis permaxillaris. Worms collected from specimens of Limnochromis auritus, a cichlid belonging to the same cichlid tribe as G. permaxillaris, were used for comparison. Morphological as well as genetic characterisation was used for parasite identification. In total, all 73 Cichlidogyrus individuals collected from 'G.' pfefferi were identified as C. irenae. This is the only representative of Cichlidogyrus previously described from 'G.' pfefferi, its type host. Gnathochromis permaxillaris is infected by a species of Cichlidogyrus morphologically very similar to C. gillardinae. The monogenean species collected from L. auritus is considered as new for science, but sample size was insufficient for a formal description. Our results confirm previous suggestions that 'G.' pfefferi as a good disperser is infected by a single monogenean species across the entire Lake Tanganyika. Although G. permaxillaris and L. auritus are placed in the same tribe, Cichlidogyrus sp. occurring on G. permaxillaris is morphologically more similar to C. irenae from 'G.' pfefferi, than to the Cichlidogyrus species found on L. auritus. Various evolutionary processes, such as host-switching or duplication events, might underlie the pattern observed in this particular parasite-host system. Additional samples for the Cichlidogyrus species occuring on G. permaxillaris and L. auritus are needed to unravel their evolutionary history by means of (co-)phylogenetic analyses.

from #Medicine via ola Kala on Inoreader http://ift.tt/1KzfxMj
via IFTTT

Age-related changes of dental pulp tissue after experimental tooth movement in rats

It is generally accepted that the effect of orthodontic tooth movement on the dental pulp in adolescents is reversible and that it has no long-lasting effect on pulpal physiology. However, it is not clear yet if the same conclusion is also valid for adult subjects. Thus, in two groups of rats, aged 6 and 40 weeks respectively, 3 molars at one side of the maxilla were moved together in a mesial direction with a standardized orthodontic appliance delivering a force of 10 cN. The contralateral side served as a control. Parasagittal histological sections were prepared after tooth movement for 1, 2, 4, 8, and 12 weeks. The pulp tissue was characterized for the different groups, with special emphasis on cell density, inflammatory cells, vascularity, and odontoblasts. Dimensions of dentin and the pulpal horns was determined and related with the duration of orthodontic force application and age ware evaluated. We found that neither in young nor in adult rats, force application led to long-lasting or irreversible changes in pulpal tissues. Dimensional variables showed significant age-related changes. In conclusion, orthodontic tooth movement per se has no long-lasting or irreversible effect on pulpal tissues, neither in the young nor in the adult animals.

from #Medicine via ola Kala on Inoreader http://ift.tt/23nk2oV
via IFTTT

Isolation and characterization of eight polymorphic microsatellites for the spotted spiny lobster, Panulirus guttatus

Microsatellite sequences were isolated from enriched genomic libraries of the spotted spiny lobster, Panulirus guttatus using 454 pyrosequencing. Twenty-nine previously developed polymerase chain reaction primer pairs of Panulirus argus microsatellite loci were also tested for cross-species amplification in Panulirus guttatus. In total, eight consistently amplifying, and polymorphic loci were characterized for 57 individuals collected in the Florida Keys and Bermuda. The number of alleles per locus ranged from 8 to 20 and observed heterozygosities ranged from 0.409 to 0.958. Significant deviations from Hardy–Weinberg equilibrium were found in one locus from Florida and three loci from Bermuda. Quality control testing indicated that all loci were easy to score, highly polymorphic and showed no evidence of linkage disequilibrium. Null alleles were detected in three loci with moderate frequencies ranging from (20% to 22%). These eight microsatellites provide novel molecular markers for future conservation genetics research of P. guttatus.

from #Medicine via ola Kala on Inoreader http://ift.tt/1KzfvnL
via IFTTT

An explicit solution for calculating optimum spawning stock size from Ricker’s stock recruitment model

Stock-recruitment models have been used for decades in fisheries management as a means of formalizing the expected number of offspring that recruit to a fishery based on the number of parents. In particular, Ricker's stock recruitment model is widely used due to its flexibility and ease with which the parameters can be estimated. After model fitting, the spawning stock size that produces the maximum sustainable yield (SMSY) to a fishery, and the harvest corresponding to it (UMSY), are two of the most common biological reference points of interest to fisheries managers. However, to date there has been no explicit solution for either reference point because of the transcendental nature of the equation needed to solve for them. Therefore, numerical or statistical approximations have been used for more than 30 years. Here I provide explicit formulae for calculating both SMSY and UMSY in terms of the productivity and density-dependent parameters of Ricker's model.

from #Medicine via ola Kala on Inoreader http://ift.tt/23nk288
via IFTTT

The feasibility and radiological features of sacral alar iliac fixation in an adult population: a 3D imaging study

Background: Surgical treatments for adult spinal deformities often include pelvic fixation, and the feasibility of sacral-2 alar iliac (S2AI) screw fixation has been shown previously. However, sometimes S2AI screw fixation cannot be applied due to the presence of an osteolytic lesion or trauma or because the biomechanical properties of only an S2AI screw is insufficient. Therefore, we questioned the feasibility of using sacral AI screws in other segments and determined whether S3AI and S4AI screws have the potential to be used for sacral fractures. The aim of this study was to investigate the feasibility and radiological features of sacral AI fixation in S1–S4 in an adult population using 3D imaging techniques. Methods: Computed tomography (CT) scans were taken of 45 patients and were imported into Mimics (Version 10.01, Materialise, Belgium) software to reconstruct the 3D digital images. Next, a cylinder (radius of 3.5 mm) was drawn to imitate the screw trajectory of a S1–4 AI screw, and every imitated screw in each segment was adjusted to a maximum upward and downward angle to acquire the feasible region. The parameters of the S1–4AI screw trajectories were measured. Results: Sacral AI screws could be successfully imitated using 3D digital imaging. The S4AI screw trajectory could be obtained in 19 of 45 patient images (42.2%), while the feasibility rates of S1AI, S2AI, and S3AI screw fixation were 100%, 100%, and 91.1% (41/45), respectively. The feasible regions of S1AI, S2AI, and S3AI screw trajectories were wide enough, while the adjustable angle of S4AI screws was very small. Conclusion: It is feasible to place S1–2AI screws in the entire adult population and S3–4AI screws in some of the adult population. Furthermore, our study suggested that 3D digital images are suitable to study the feasibility of new screw fixation.

from #Medicine via ola Kala on Inoreader http://ift.tt/23nk0xa
via IFTTT

Molecular evidence for sediment nitrogen fixation in a temperate New England estuary

Primary production in coastal waters is generally nitrogen (N) limited with denitrification outpacing nitrogen fixation (N2-fixation). However, recent work suggests that we have potentially underestimated the importance of heterotrophic sediment N2-fixation in marine ecosystems. We used clone libraries to examine transcript diversity of nifH (a gene associated with N2-fixation) in sediments at three sites in a temperate New England estuary (Waquoit Bay, Massachusetts, USA) and compared our results to net sediment N2 fluxes previously measured at these sites. We observed nifH expression at all sites, including a site heavily impacted by anthropogenic N. At this N impacted site, we also observed mean net sediment N2-fixation, linking the geochemical rate measurement with nifH expression. This same site also had the lowest diversity (non-parametric Shannon = 2.75). At the two other sites, we also detected nifH transcripts, however, the mean N2 flux indicated net denitrification. These results suggest that N2-fixation and denitrification co-occur in these sediments. Of the unique sequences in this study, 67% were most closely related to uncultured bacteria from various marine environments, 17% to Cluster III, 15% to Cluster I, and only 1% to Cluster II. These data add to the growing body of literature that sediment heterotrophic N2-fixation, even under high inorganic nitrogen concentrations, may be an important yet overlooked source of N in coastal systems.

from #Medicine via ola Kala on Inoreader http://ift.tt/1Kzfv6Z
via IFTTT

Structural strength of cancellous specimens from bovine femur under cyclic compression

The incidence of osteoporotic fractures was estimated as nine million worldwide in 2000, with particular occurrence at the proximity of joints rich in cancellous bone. Although most of these fractures spontaneously heal, some fractures progressively collapse during the early post-fracture period. Prediction of bone fragility during progressive collapse following initial fracture is clinically important. However, the mechanism of collapse, especially the gradual loss of the height in the cancellous bone region, is not clearly proved. The strength of cancellous bone after yield stress is difficult to predict since structural and mechanical strength cannot be determined a priori. The purpose of this study was to identify whether the baseline structure and volume of cancellous bone contributed to the change in cancellous bone strength under cyclic loading. A total of fifteen cubic cancellous bone specimens were obtained from two 2-year-old bovines and divided into three groups by collection regions: femoral head, neck, and proximal metaphysis. Structural indices of each 5-mm cubic specimen were determined using micro-computed tomography. Specimens were then subjected to five cycles of uniaxial compressive loading at 0.05 mm/min with initial 20 N loading, 0.3 mm displacement, and then unloading to 0.2 mm with 0.1 mm displacement for five successive cycles. Elastic modulus and yield stress of cancellous bone decreased exponentially during five loading cycles. The decrease ratio of yield stress from baseline to fifth cycle was strongly correlated with bone volume fraction (BV/TV, r = 0.96, p

from #Medicine via ola Kala on Inoreader http://ift.tt/23njYFE
via IFTTT

Dentistry Journal, Vol. 4, Pages 2: Tobacco, Alcohol and Drug Use among Dental Undergraduates at One UK University in 2015

The aim of this study was determine the prevalence of tobacco, alcohol and illicit substance use among dental undergraduates at one UK university in 2015. A cross-sectional survey of all 344 dental undergraduates using an anonymous self-report questionnaire was carried out. The response rate was 77%, of which 29% were male and 71% female. Tobacco smoking was reported by 23.6% of males and 12.2% of females, with only 1.6% of females reporting to smoke ≥10 cigarettes per day. Alcohol consumption was reported by 85.5% of males and 84% of females, and reported levels of alcohol consumption increased since becoming undergraduates. Binge drinking was reported by 35.3% of males and 41% of female students. Only 2.6% of males and 0.5% of females reported to be current regular users of cannabis. The vast majority of respondents claimed to have never used any illicit substance. The only other reported regularly used substances by males was Ecstasy (1.3%) and by females were LSD (0.5%), Ecstasy (1.5%), Cocaine (0.5%), Inhalants (0.5%) and Ketamine (0.5%). These results are encouraging. Fewer students reported smoking than in the general population, levels of binge drinking were considerably lower than previously reported figures, as were the numbers of regular users of cannabis and other illicit substances.

from #Medicine via ola Kala on Inoreader http://ift.tt/1S5mFZ3
via IFTTT

Sensors, Vol. 16, Pages 147: 3D Markov Process for Traffic Flow Prediction in Real-Time

Recently, the correct estimation of traffic flow has begun to be considered an essential component in intelligent transportation systems. In this paper, a new statistical method to predict traffic flows using time series analyses and geometric correlations is proposed. The novelty of the proposed method is two-fold: (1) a 3D heat map is designed to describe the traffic conditions between roads, which can effectively represent the correlations between spatially- and temporally-adjacent traffic states; and (2) the relationship between the adjacent roads on the spatiotemporal domain is represented by cliques in MRF and the clique parameters are obtained by example-based learning. In order to assess the validity of the proposed method, it is tested using data from expressway traffic that are provided by the Korean Expressway Corporation, and the performance of the proposed method is compared with existing approaches. The results demonstrate that the proposed method can predict traffic conditions with an accuracy of 85%, and this accuracy can be improved further.

from #Medicine via ola Kala on Inoreader http://ift.tt/1lJCrKn
via IFTTT

Administrative Sciences, Vol. 6, Pages 2: Acknowledgement to Reviewers of Administrative Sciences in 2015

The editors of Administrative Sciences would like to express their sincere gratitude to the following reviewers for assessing manuscripts in 2015. [...]

from #Medicine via ola Kala on Inoreader http://ift.tt/1lJCru0
via IFTTT

Sensors, Vol. 16, Pages 149: Improved Circuits with Capacitive Feedback for Readout Resistive Sensor Arrays

One of the most suitable ways of distributing a resistive sensor array for reading is an array with M rows and N columns. This allows reduced wiring and a certain degree of parallelism in the implementation, although it also introduces crosstalk effects. Several types of circuits can carry out the analogue-digital conversion of this type of sensors. This article focuses on the use of operational amplifiers with capacitive feedback and FPGAs for this task. Specifically, modifications of a previously reported circuit are proposed to reduce the errors due to the non-idealities of the amplifiers and the I/O drivers of the FPGA. Moreover, calibration algorithms are derived from the analysis of the proposed circuitry to reduce the crosstalk error and improve the accuracy. Finally, the performances of the proposals is evaluated experimentally on an array of resistors and for different ranges.

from #Medicine via ola Kala on Inoreader http://ift.tt/1lJCrtM
via IFTTT

Sensors, Vol. 16, Pages 151: Evaluation of the Bitterness of Traditional Chinese Medicines using an E-Tongue Coupled with a Robust Partial Least Squares Regression Method

To accurately, safely, and efficiently evaluate the bitterness of Traditional Chinese Medicines (TCMs), a robust predictor was developed using robust partial least squares (RPLS) regression method based on data obtained from an electronic tongue (e-tongue) system. The data quality was verified by the Grubb's test. Moreover, potential outliers were detected based on both the standardized residual and score distance calculated for each sample. The performance of RPLS on the dataset before and after outlier detection was compared to other state-of-the-art methods including multivariate linear regression, least squares support vector machine, and the plain partial least squares regression. Both R2 and root-mean-squares error (RMSE) of cross-validation (CV) were recorded for each model. With four latent variables, a robust RMSECV value of 0.3916 with bitterness values ranging from 0.63 to 4.78 were obtained for the RPLS model that was constructed based on the dataset including outliers. Meanwhile, the RMSECV, which was calculated using the models constructed by other methods, was larger than that of the RPLS model. After six outliers were excluded, the performance of all benchmark methods markedly improved, but the difference between the RPLS model constructed before and after outlier exclusion was negligible. In conclusion, the bitterness of TCM decoctions can be accurately evaluated with the RPLS model constructed using e-tongue data.

from #Medicine via ola Kala on Inoreader http://ift.tt/1S5mDQW
via IFTTT

Behavioral Sciences, Vol. 6, Pages 6: Acknowledgement to Reviewers of Behavioral Sciences in 2015

The editors of Behavioral Sciences would like to express their sincere gratitude to the following reviewers for assessing manuscripts in 2015. [...]

from #Medicine via ola Kala on Inoreader http://ift.tt/1UlDVXa
via IFTTT

Materials, Vol. 9, Pages 70: Building Energy Storage Panel Based on Paraffin/Expanded Perlite: Preparation and Thermal Performance Study

This study is focused on the preparation and performance of a building energy storage panel (BESP). The BESP was fabricated through a mold pressing method based on phase change material particle (PCMP), which was prepared in two steps: vacuum absorption and surface film coating. Firstly, phase change material (PCM) was incorporated into expanded perlite (EP) through a vacuum absorption method to obtain composite PCM; secondly, the composite PCM was immersed into the mixture of colloidal silica and organic acrylate, and then it was taken out and dried naturally. A series of experiments, including differential scanning calorimeter (DSC), scanning electron microscope (SEM), best matching test, and durability test, have been conducted to characterize and analyze the thermophysical property and reliability of PCMP. Additionally, the thermal performance of BESP was studied through a dynamic thermal property test. The results have showed that: (1) the surface film coating procedure can effectively solve the leakage problem of composite phase change material prepared by vacuum impregnation; (2) the optimum adsorption ratio for paraffin and EP was 52.5:47.5 in mass fraction, and the PCMP has good thermal properties, stability, and durability; and (3) in the process of dynamic thermal performance test, BESP have low temperature variation, significant temperature lagging, and large heat storage ability, which indicated the potential of BESP in the application of building energy efficiency.

from #Medicine via ola Kala on Inoreader http://ift.tt/1K6b8FR
via IFTTT

Remote Sensing, Vol. 8, Pages 82: A Linear Feature-Based Approach for the Registration of Unmanned Aerial Vehicle Remotely-Sensed Images and Airborne LiDAR Data

Compared with traditional manned airborne photogrammetry, unmanned aerial vehicle remote sensing (UAVRS) has the advantages of lower cost and higher flexibility in data acquisition. It has, therefore, found various applications in fields such as three-dimensional (3D) mapping, emergency management, and so on. However, due to the instability of the UAVRS platforms and the low accuracy of the onboard exterior orientation (EO) observations, the use of direct georeferencing image data leads to large location errors. Light detection and ranging (LiDAR) data, which is highly accurate 3D information, is treated as a complementary data source to the optical images. This paper presents a semi-automatic approach for the registration of UAVRS images and airborne LiDAR data based on linear control features. The presented approach consists of three main components, as follows. (1) Buildings are first separated from the point cloud by the integrated use of height and size filtering and RANdom SAmple Consensus (RANSAC) plane fitting, and the 3D line segments of the building ridges and boundaries are semi-automatically extracted through plane intersection and boundary regularization with manual selections; (2) the 3D line segments are projected to the image space using the initial EO parameters to obtain the approximate locations, and all the corresponding 2D line segments are semi-automatically extracted from the UAVRS images. Meanwhile, the tie points of the UAVRS images are generated using a Förstner operator and least-squares image matching; and (3) by use of the equations derived from the coplanarity constraints of the linear control features and the colinear constraints of the tie points, block bundle adjustment is carried out to update the EO parameters of the UAVRS images in the coordinate framework of the LiDAR data, achieving the co-registration of the two datasets. Experiments were performed to demonstrate the validity and effectiveness of the presented method, and a comparison with the traditional registration method based on LiDAR intensity images showed that the presented method is more accurate, and a sub-pixel accuracy level can be achieved.

from #Medicine via ola Kala on Inoreader http://ift.tt/1S5gqnO
via IFTTT

Challenges, Vol. 7, Pages 1: Acknowledgement to Reviewers of Challenges in 2015

The editors of Challenges would like to express their sincere gratitude to the following reviewers for assessing manuscripts in 2015. [...]

from #Medicine via ola Kala on Inoreader http://ift.tt/1ORkMJ5
via IFTTT

Axioms, Vol. 5, Pages 3: Acknowledgement to Reviewers of Axioms in 2015

The editors of Axioms would like to express their sincere gratitude to the following reviewers for assessing manuscripts in 2015. [...]

from #Medicine via ola Kala on Inoreader http://ift.tt/1ORkMsF
via IFTTT

Molbank, Vol. 2016, Article M887: Acknowledgement to Reviewers of Molbank in 2015

The editors of Molbank would like to express their sincere gratitude to the following reviewers for assessing manuscripts in 2015. [...]

from #Medicine via ola Kala on Inoreader http://ift.tt/1ntwWS3
via IFTTT

Microarrays, Vol. 5, Pages 4: Acknowledgement to Reviewers of Microarrays in 2015

The editors of Microarrays would like to express their sincere gratitude to the following reviewers for assessing manuscripts in 2015. [...]

from #Medicine via ola Kala on Inoreader http://ift.tt/1ORkMst
via IFTTT

Micromachines, Vol. 7, Pages 18: Devices Based on Co-Integrated MEMS Actuators and Optical Waveguide: A Review

The convergence of Micro Electro Mechanical Systems (MEMS) and optics was, at the end of the last century, a fertile ground for a new breed of technological and scientific achievements. The weightlessness of light has been identified very early as a key advantage for micro-actuator application, giving rise to optical free-space MEMS devices. In parallel to these developments, the past 20 years saw the emergence of a less pursued approach relying on guided optical wave, where, pushed by the similarities in fabrication process, researchers explored the possibilities offered by merging integrated optics and MEMS technology. The interest of using guided waves is well known (absence of diffraction, tight light confinement, small size, compatibility with fiber optics) but it was less clear how they could be harnessed with MEMS technology. Actually, it is possible to use MEMS actuators for modifying waveguide properties (length, direction, index of refraction) or for coupling light between waveguide, enabling many new devices for optical telecommunication, astronomy or sensing. With the recent expansion to nanophotonics and optomechanics, it seems that this field still holds a lot of promises.

from #Medicine via ola Kala on Inoreader http://ift.tt/1ntwXp3
via IFTTT

Processes, Vol. 4, Pages 4: State Observer Design for Monitoring the Degree of Polymerization in a Series of Melt Polycondensation Reactors

A nonlinear reduced-order state observer is applied to estimate the degree of polymerization in a series of polycondensation reactors. The finishing stage of polyethylene terephthalate synthesis is considered in this work. This process has a special structure of lower block triangular form, which is properly utilized to facilitate the calculation of the state-dependent gain in the observer design. There are two possible on-line measurements in each reactor. One is continuous, and the other is slow-sampled with dead time. For the slow-sampled titration measurement, inter-sample behavior is estimated from an inter-sample output predictor, which is essential in providing continuous corrections on the observer. Dead time compensation is carried out in the same spirit as the Smith predictor to reduce the effect of delay in the measurement outputs. By integrating the continuous-time reduced-order observer, the inter-sample predictor and the dead time compensator together, the degree of polymerization is accurately estimated in all reactors. The observer performance is demonstrated by numerical simulations. In addition, a pre-filtering technique is used in the presence of sensor noise.

from #Medicine via ola Kala on Inoreader http://ift.tt/1ORkLVC
via IFTTT

Molecules, Vol. 21, Pages 135: Coumarins as Potential Antioxidant Agents Complemented with Suggested Mechanisms and Approved by Molecular Modeling Studies

Syntheses of coumarins, which are a structurally interesting antioxidant activity, was done in this article. The modification of 7-hydroxycoumarin by different reaction steps was done to yield target compounds. Molecular structures were characterized by different spectroscopical techniques (Fourier transformation infrared and nuclear magnetic resonance). Antioxidant activities were performed by using various in vitro spectrophometric assays against 1,1-diphenyl-2-picrylhydrazyl (DPPH) radical and hydrogen peroxide (H2O2). All compounds exhibited high efficiency as antioxidants compared to ascorbic acid. The highest efficiency scavenging activity was found for compound 3 (91.0 ± 5.0), followed by compounds 2 and 4 (88.0 ± 2.00; and 87.0 ± 3.00). Ascorbic acid C was used as a standard drug with a percentage inhibition of 91.00 ± 1.5. The mechanism of the synthesized compounds as antioxidants was also studied. Hartree–Fock–based quantum chemical studies have been carried out with the basis set to 3-21G, in order to obtain information about the three-dimensional (3D) geometries, electronic structure, molecular modeling, and electronic levels, namely HOMO (highest occupied molecular orbital) and LUMO (lowest unoccupied molecular orbital), to understand the antioxidant activity for the synthesized compounds.

from #Medicine via ola Kala on Inoreader http://ift.tt/1ntwWBp
via IFTTT

Regulation of the T-type Ca2+ channel Cav3.2 by hydrogen sulfide: Emerging controversies concerning the role of H2S in nociception

Abstract

Ion channels represent a large and growing family of target proteins regulated by gasotransmitters such as nitric oxide, carbon monoxide and, as described more recently, hydrogen sulfide. Indeed, many of the biological actions of these gases can be accounted for by their ability to modulate ion channel activity. Here, we report recent evidence that H₂S is a modulator of low voltage-activated T-type Ca²⁺ channels, and discriminates between the different subtypes of T-type Ca²⁺ channel in that it selectively modulates Cav3.2, whilst Cav3.1 and Cav3.3 are unaffected. At high concentrations, H₂S augments Cav3.2 currents, an observation which has led to the suggestion that H₂S exerts its pro-nociceptive effects via this channel, since Cav3.2 plays a central role in sensory nerve excitability. However, at more physiological concentrations, H₂S is seen to inhibit Cav3.2. This inhibitory action requires the presence of the redox-sensitive, extracellular region of the channel which is responsible for tonic metal ion binding, and which particularly distinguishes this channel isoform from Cav3.1 and 3.3. Further studies indicate that H₂S may act in a novel manner to alter channel activity by potentiating the zinc sensitivity / affinity of this binding site. This review discusses the different reports of H₂S modulation of T-type Ca²⁺ channels, and how such varying effects may impact on nociception, given the role of this channel in sensory activity. This subject remains controversial, and future studies are required before the impact of T-type Ca²⁺ channel modulation by H₂S might be exploited as a novel approach to pain management.

This article is protected by copyright. All rights reserved

from #Medicine via ola Kala on Inoreader http://ift.tt/1ntvMG0
via IFTTT

IJERPH, Vol. 13, Pages 156: Smoke-Free Public Policies and Voluntary Policies in Personal Settings in Tbilisi, Georgia: A Qualitative Study

Georgia has limited tobacco control policies, particularly in the area of smoke-free public policies, which may influence the adoption of smoke-free home rules. We qualitatively examined knowledge about and reactions to public and personal smoke-free policies among Tbilisi residents. In Spring 2014, we conducted six focus groups among 47 total participants—two among male smokers, one among male nonsmokers, two among female smokers, and one among female nonsmokers. Our sample was 48.9% male and 70.2% past 30-day smokers. Most believed that SHS was dangerous, with particular concern regarding the impact of SHS on children and pregnant women. Many had misconceptions about how to protect others from SHS and the effectiveness of some approaches. Many indicated that they had some type of home rules, but few reported a complete ban on smoking in the home. Even when some restrictions were in place, they rarely were effective or enforced. Common concerns about the partial smoke-free public policy in Georgia included its economic impact, perceived discrimination among smokers, and the policy being against the Georgian culture. These concerns were heightened when participants were asked about the possible implementation of a complete smoke-free policy. Educational programs are needed to promote smoke-free policies in Georgia.

from #Medicine via ola Kala on Inoreader http://ift.tt/23n6bPn
via IFTTT

Aerospace, Vol. 3, Pages 4: The Effect of the Phase Angle between the Forewing and Hindwing on the Aerodynamic Performance of a Dragonfly-Type Ornithopter

Dragonflies achieve agile maneuverability by flapping four wings independently. Different phase angles between the flapping forewing and hindwing have been observed during various flight modes. The aerodynamic performance depends on phase angle control, as exemplified by an artificial flying ornithopter. Here, we present a dragonfly-like ornithopter whose phase angle was designed to vary according to the phase lag between the slider-cranks of the forewing and hindwing. Two microelectromechanical systems (MEMS) differential pressure sensors were attached to the center of both forewing and hindwing to evaluate the aerodynamic performance during flapping motions when the phase angle was changed. By varying the phase angle in both the tethered condition and free-flight, the performance of the forewing remained approximately constant, whereas that of the hindwing exhibited obvious variations; the maximum average value was two-fold higher than the minimum. The experimental results suggest that simple phase angle changes enable a flying ornithopter to control flight force balance without complex changes in the wing kinematics.

from #Medicine via ola Kala on Inoreader http://ift.tt/1S5cfZm
via IFTTT

Micromachines, Vol. 7, Pages 17: Numerical Investigation of Cell Encapsulation for Multiplexing Diagnostic Assays Using Novel Centrifugal Microfluidic Emulsification and Separation Platform

In the present paper, we report a novel centrifugal microfluidic platform for emulsification and separation. Our design enables encapsulation and incubation of multiple types of cells by droplets, which can be generated at controlled high rotation speed modifying the transition between dripping-to-jetting regimes. The droplets can be separated from continuous phase using facile bifurcated junction design. A three dimensional (3D) model was established to investigate the formation and sedimentation of droplets using the centrifugal microfluidic platform by computational fluid dynamics (CFD). The simulation results were compared to the reported experiments in terms of droplet shape and size to validate the accuracy of the model. The influence of the grid resolution was investigated and quantified. The physics associated with droplet formation and sedimentation is governed by the Bond number and Rossby number, respectively. Our investigation provides insight into the design criteria that can be used to establish centrifugal microfluidic platforms tailored to potential applications, such as multiplexing diagnostic assays, due to the unique capabilities of the device in handling multiple types of cells and biosamples with high throughput. This work can inspire new development of cell encapsulation and separation applications by centrifugal microfluidic technology.

from #Medicine via ola Kala on Inoreader http://ift.tt/1lJrcBL
via IFTTT

JCDD, Vol. 3, Pages 3: Long-term Benefits of Risk Factor Reduction in Takotsubo Cardiomyopathy.—A Comment on Khalighi et al. Entitled “Takotsubo Cardiomyopathy: A Long Term Follow-up Shows Benefit with Risk Factor Reduction”, J. Cardiovasc. Dev. Dis., 2015, 2, 273–281.

Takotsubo cardiomyopathy (TC) or stress-induced cardiomyopathy is also popularly referred to as "broken heart syndrome" or "apical ballooning syndrome". [...]

from #Medicine via ola Kala on Inoreader http://ift.tt/1S5ceom
via IFTTT

Gels, Vol. 2, Pages 6: Stimuli Responsive Poly(Vinyl Caprolactam) Gels for Biomedical Applications

Poly(vinyl caprolactam) (PNVCL) is one of the most important thermoresponsive polymers because it is similar to poly(N-isopropyl acrylamide). PNVCL precipitates from aqueous solutions in a physiological temperature range (32–34 °C). The use of PNVCL instead of PNIPAM is considered advantageous because of the assumed lower toxicity of PNVCL. PNVCL copolymer gels are sensitive to external stimuli, such as temperature and pH; which gives them a wide range of biomedical applications and consequently attracts considerable scientific interest. This review focuses on the recent studies on PNVCL-based stimuli responsive three dimensional hydrogels (macro, micro, and nano) for biomedical applications. This review also covers the future outlooks of PNVCL-based gels for biomedical applications, particularly in the drug delivery field.

from #Medicine via ola Kala on Inoreader http://ift.tt/1S5ccws
via IFTTT

Membranes, Vol. 6, Pages 2: Acknowledgement to Reviewers of Membranes in 2015

The editors of Membranes would like to express their sincere gratitude to the following reviewers for assessing manuscripts in 2015. [...]

from #Medicine via ola Kala on Inoreader http://ift.tt/1QLmZeq
via IFTTT

Fermentation, Vol. 2, Pages 3: Characterizing the Phenotypic Responses of Escherichia coli to Multiple 4-Carbon Alcohols with Raman Spectroscopy

The phenotypic responses of E. coli cells exposed to 1.2% (v/v) of 1-butanol, 2-butanol, isobutanol, tert-butanol, and 1,4-butanediol were studied in near real-time using Raman spectroscopy. A method of "chemometric fingerprinting" was employed that uses multivariate statistics (principal component analysis and linear discriminant analysis) to identify E. coli phenotypic changes over a 180 min post-treatment time-course. A toxicity study showed extreme variability among the reduction in culture growth, with 1-butanol showing the greatest toxicity and 1,4-butanediol showing relatively no toxicity. Chemometric fingerprinting showed distinct phenotype clusters according to the type of alcohol: (i) 1-butanol and 2-butanol (straight chain alcohols); (ii) isobutanol and tert-butanol (branched chain alcohols); and (iii) control and 1,4-butanediol (no terminal alkyl end) treated cells. While the isobutanol and tert-butanol treated cells led to similar phenotypic responses, isobutanol was significantly more toxic. In addition, the phenotypic response was found to take place largely within 60 min of culture treatment; however, significant responses (especially for 1,4-butanediol) were still occurring at 180 min post-treatment. The methodology presented here identified different phenotypic responses to seemingly similar 4-carbon alcohols and can be used to study phenotypic responses of virtually any cell type under any set of environmental conditions or genetic manipulations.

from #Medicine via ola Kala on Inoreader http://ift.tt/1S5cdAD
via IFTTT

Materials, Vol. 9, Pages 68: Mechanical Strength Improvements of Carbon Nanotube Threads through Epoxy Cross-Linking

Individual Carbon Nanotubes (CNTs) have a great mechanical strength that needs to be transferred into macroscopic fiber assemblies. One approach to improve the mechanical strength of the CNT assemblies is by creating covalent bonding among their individual CNT building blocks. Chemical cross-linking of multiwall CNTs (MWCNTs) within the fiber has significantly improved the strength of MWCNT thread. Results reported in this work show that the cross-linked thread had a tensile strength six times greater than the strength of its control counterpart, a pristine MWCNT thread (1192 MPa and 194 MPa, respectively). Additionally, electrical conductivity changes were observed, revealing 2123.40 S·cm−1 for cross-linked thread, and 3984.26 S·cm−1 for pristine CNT thread. Characterization suggests that the obtained high tensile strength is due to the cross-linking reaction of amine groups from ethylenediamine plasma-functionalized CNT with the epoxy groups of the cross-linking agent, 4,4-methylenebis(N,N-diglycidylaniline).

from #Medicine via ola Kala on Inoreader http://ift.tt/1S5cdk9
via IFTTT

Marine Drugs, Vol. 14, Pages 20: Larvicidal Potential of the Halogenated Sesquiterpene (+)-Obtusol, Isolated from the Alga Laurencia dendroidea J. Agardh (Ceramiales: Rhodomelaceae), against the Dengue Vector Mosquito Aedes aegypti (Linnaeus) (Diptera: Culicidae)

Dengue is considered a serious public health problem in many tropical regions of the world including Brazil. At the moment, there is no viable alternative to reduce dengue infections other than controlling the insect vector, Aedes aegypti Linnaeus. In the continuing search for new sources of chemicals targeted at vector control, natural products are a promising alternative to synthetic pesticides. In our work, we investigated the toxicity of a bioactive compound extracted from the red alga Laurencia dendroidea J. Agardh. The initial results demonstrated that crude extracts, at a concentration of 5 ppm, caused pronounced mortality of second instar A. aegypti larvae. Two molecules, identified as (−)-elatol and (+)-obtusol were subsequently isolated from crude extract and further evaluated. Assays with (−)-elatol showed moderate larvicidal activity, whereas (+)-obtusol presented higher toxic activity than (−)-elatol, with a LC50 value of 3.5 ppm. Histological analysis of the larvae exposed to (+)-obtusol revealed damage to the intestinal epithelium. Moreover, (+)-obtusol-treated larvae incubated with 2 µM CM-H2DCFDA showed the presence of reactive oxygen species, leading us to suggest that epithelial damage might be related to redox imbalance. These results demonstrate the potential of (+)-obtusol as a larvicide for use against A. aegypti and the possible mode of action of this compound.

from #Medicine via ola Kala on Inoreader http://ift.tt/1lJrad6
via IFTTT